Rayonix HS (High Speed) CCD Detector Series

  • MX340-HS: 16 chip high speed mosaic CCD detector with 340 mm x 340 mm active area and 2.9:1 taper ratio

    MX340-HS high speed CCD detector

  • MX225-HS: 4 chip high speed mosaic CCD detector with 225 mm x 225 mm active area and 2.9:1 taper ratio

    MX225-HS high speed CCD detector

  • SX85-HS: single chip high speed CCD detector with 85 mm x 85 mm active area and 2.9:1 taper ratio

    SX85-HS high speed CCD detector

  • LX170-HS: 2 chip high speed mosaic CCD detector with 85 x mm x 170 mm active area and 2.9:1 taper ratio for SAXS/WAXS

    LX170-HS high speed CCD detector

  • LX255-HS: 3 chip high speed mosaic CCD detector with 85 x mm x 255 mm active area and 2.9:1 taper ratio for SAXS/WAXS

    LX255-HS high speed CCD detector

MarXperts is proud to be distributor (outside the Americas) of the world’s most advanced large area CCD-based X-ray detectors manufactured by Rayonix, LLC, USA.

The HS series is the latest addition to the line of CCD-detectors. It implements leading frame transfer technology that makes the new detectors as fast as pixel detectors (up to 140 frames/second) without compromising data quality and resolution. Thus, the HS detectors are ideally suited for experimental conditions where the read-out time of a detector becomes the bottleneck and not the amount of available X-ray photons, i.e. mostly on high brilliance synchrotron sites. Typical usage include high throughput single crystal crystallography including time-resolved studies, small- and wide angle scattering experiments (SAXS/WAXS), powder diffraction, X-ray computed tomography. Without the count-rate limitations of the competing pixel detectors, they are equally well suited for the upcoming X-ray electron laser beamlines (XFEL).

The detectors are available as single chip detectors (SX-30, SX-85) or as mosaic arrangements with 2x2, 3x3, 4x4 or 5x5 arrays with varying fibre optic taper sizes. In order to allow SAXS to pass through while measuring WAXS, scientists have been asking for an X-ray detector with a hole in the middle. The resulting LX series has a long, rectangular detecting surface, engineered with a notch to allow the direct beam and SAXS data to pass through.

Despite of their modular setup, the mosaic detectors come without gaps between the individual modules which is a considerable advantage over competing pixel detectors. The models differ most distinctively in the amount of built-in CCD-chips and the corresponding active area.  The following table gives an overview of specifications common to the entire series and point out the few relevant differences.


    All HS-series detectors are based on a custom design CCD-sensor sized 3 x 3 cm with 1920 x 1920 pixels. A fiber optic taper is permanently bound to the sensor using a patented technology. The fiber optic tapers use demagnification ratios of 1:1, 1:2.6 or 2.92 yielding detectors with very large surfaces, depending on the amount of sensor modules.
    Custom electronics provide ultra-low readout noise at high readout speeds: either 8e- in high speed mode or 4e- in low noise mode. The read-out time of a full frame is approx. 400 msec. With a typical binning mode of 2x2, the read-out time drops to 100 msec (10 frames/sec). With a 10 x 10 binning, a single frame is produced in 7 ms (140 frames/sec). The dead-time between images is 1 msec.
    The CCD sensor is cooled to -80°C and protected inside a sealed vacuum chamber. The resulting dark current, less than 0.003e-/pixel/sec., allows exposures long enough for data collection from any crystal on any X-ray source. The refrigeration system requires only a standard electrical outlet and no cooling water.
    The detectors are calibrated carefully before delivery. Due to the permanent bond between the fiber-optic taper and the CCD chip, the instrument does not require routine recalibration.

Comparison chart

Model SX-30 SX-85 MX-170 MX-225 MX-300 MX-340 MX-425
X-ray sensitive surface [mm x mm] 30 x 30 85 x 85 170 x 170 225 x 225 300 x 300 340 x 340 425 x 425
Number of CCD-chips 1 1 4 9 16 16 25
Fiber-optic taper demagnification ratio 1 : 1 2.92 : 1 2.92 : 1 2.60 : 1 2.60 : 1 2.92 : 1 2.92 : 1
Pixel in full image 19202 19202 38402 57602 76802 76802 96002
Pixel size in full image [μm] 16 44 44 39 39 44 44
Model LX-170 LX-255
X-ray sensitive surface [mm x mm] 85 x 170 85 x 255
Number of CCD-chips 2 3
Fiber-optic taper demagnification ratio 2.92 : 1 2.92 : 1
Pixel in full image 1920 x 3840 1920 x 5760
Pixel size in full image [μm] 44 44

Common technical data:

Detective quantum efficiency (DQE) at 8-12 keV up to 0.8
Point spread function FWHM < 100 μm
FW 1% < 300 μm
Gain (electrons per 12 keV X-ray photon) 70 e¯
Read-out noise in standard readout mode < 8 e¯/pixel
Pixels per chip 1920 x 1920
No. of on-chip read-out channels 16
Dark current at -80°C ≤ 0.003 e¯/pixel/sec
Full well capacity for 12 keV photons 400 ke¯/pixel
Dynamic range 16 bits
Phosphor Gd2O2S:Tb <40 μm thick
Weight < 60 kg

Get in touch

Our team will be glad to help you anytime with general
or technical questions, suggestions or comments.